Cockshutt 10 Series

Fourty · Fourty

Ive recently brought home a Cockshutt 40 with a 230 Buda. The distributor is pretty worn, with quite a lot of side to side slop in the shaft which is making setting the points a challenge. Its an Autolite IAD 6001 1B. Im having trouble locating a new bushing or mechanical advance springs. Any parts I have...

Andrus · Andrus

Can anyone recommend a good outfit, or person, to rebuild the governor for my 30?

Farmerbrowne · Farmerbrowne

Howdy yall Im new to the cockshutt tractors and just picked one up for 300 bucks. Am i right to assume its from late 1930s with the following cast number of 47-80-6043

colorado502 · colorado502

anyone knows if there is a replacement for the cockshutt 30 starter. something better. been rebuilding mine for the third time and still fail. thanks

BBaker · BBaker

the gear shift moves all around in circles instead of in a precise gear shift pattern. For example I need to push the shifter to the left with my foot to get it in Reverse. Any thoughts out There? - Brett Baker

Kruser · Kruser

Exactly as the title asks. I need to fill the PTO assembly with oil. What type does it take?

Swen Nilsson · Swen Nilsson

I am rather new to the Cockshutt/Co-op world, but I have noticed the the steering shaft seems to like to rust/freeze solid in the cast iron housing up by the instruments. What is the best way to get the shaft loose again?

Kruser · Kruser

Putting together a Buda 4B153 and I was wondering what would be the best source for a new oil fill tube. The block I am using doesn't have one. Before I start putting too much time into this, does anybody have a source for this or can you point me to the right direction?

Swen Nilsson · Swen Nilsson

I recently acquired a Cockshutt 30. The one front wheel hub was off as the bearing was shot. I am trying to put things back to together. I have a diagram in a service manual, but not a parts book. There is a "washer" that apparently goes into the seal retainer. Is the "washer" a metal washer, or is it a f...

Kruser · Kruser

I'm looking to repaint a 1947 Coop E3. The paint supplier wants a paint number before he will sell me any. Anybody wish to give me the correct paint number? TIA.

JOHN PERUSELLO · JOHN PERUSELLO

I have some question's about the wheels on the Cockshutt 30's.when did Cockshutt start using the cast spoked rear wheels were these only on early or later tractors or were they an option.the same goes for the front wheels anybody know?.John -- Edited by JOHN PERUSELLO on Saturday 30th of March 2013 10...

skinny9976 · skinny9976

Hey guys whats this radiator out of a 40 worth. Was good when pulled been hanging in my garage since.

Neil · Neil

Need some help, restoring a 1953 Cockshutt 30, Stearing gear box is made by Ross W262999 and I cannot find the input shaft seal. The seal I pulled out of it has the numbers GK120N056 on it. Any help in finding a new seal is greatly appreciated

coope3 · coope3

I have a 1952 cockshutt 20 need wiring diagram to rewire it the wright way . Thanks alot

Buda · Buda

Hi folks,I have a 50 wide front that I use to compete in antique tractor pulls with.After pulling for over 20 yrs. it is still very successfull pulling in classes over 6000 lbs.I've been thinking it's time to make a small change just to mix things up a bit.I would like to switch to a narrow front end t...

Buda · Buda

Hi folks:I have owned and loved Cockshutts for over 20 years,but am new to your forum.Please bear with me while I bore you with my Cockshutt story.When I got into antique tractor pulling about 25 yrs. ago.I wanted something differant then the Farmalls and JDs that were common around here,so I bough...

dano · dano

Looking for a little help. I am like Buda last year and want to put a narrow front on my 40 PD.. I have the wide front off and the shafts apart. Found a 30 narrow front and the cast pedistal bolts right up. The holes in the pedistall will need to be re-drilled to fit the tower. Looks like I will have to cut the sha...

Mike(NEOhio) · Mike(NEOhio)

See my post on the Buda section.

ikeever · ikeever

Anyone have a part number for me? Unable to get to my cockshutt parts manual at the moment...timken number would be best!

ikeever · ikeever

Ever since I put that thinner head gasket on my 50 gas, I've got considerable piston slap...does a thicker oil help with this at all? Synthetic oil? It is not bad, just looking for a way to quite it down a bit. Buda guys any tips?

ndmcsx · ndmcsx

I just purchased a co op e3 diesel(paint underneath is orange) with serial number 30D33418 and was wondering a couple of things since I am new to these tractors. Where is the best place to get parts for this buda diesel? Where is the best place to get parts(new and used)in general for these? How many...

cowman61 · cowman61

Just got my 30, wanted one for years, 8 spd, live power, question about gear shift - little pin on left side facing forward, moves in and out - not supposed to ? If it moves out too far, gear shift gets loose. Pulled it out , does not go all way through. How is this supposed to be held in? Pic attached, still som...

ikeever · ikeever

Does anyone have any pictures of a power steering setup on a 50. I'm thinking about rigging one up and want it to look as close to stock as possible. isaackeever@gmail.com

colorado502 · colorado502

started to run great at idle and then at full power,its run like if it was not breathing or maybe to much air, but idle run great, rebuit the fire and fuel system, still the same. anyone have any idea?

lee troop · lee troop

Hi My name is Lee. I'm from Nova Scotia, Canada. I have a 1955 Cockshutt. It's in good shape sheet metal wise. I'm wondering what this tractor is worth? If anyone has information on my machine it would be greatly appreciated.

Mike(NEOhio) · Mike(NEOhio)

Tenny, send me your email address by private message. I'll shoot you those front end diagrams.

reebok · reebok

I have a chance to aquire a 40 but the original engine is out of it, what is the chance of finding an original engine? What is an adjustable wide front end for the same tractor worth?

Daniel_Parent · Daniel_Parent

I am looking for advice on warming up the engine of my Cockshutt 30 before starting it (it's about to get very cold up here). There is very little space to put in a standard heater in the lower radiator hose. It's basically all metal with a small hose connecting the two parts. I suppose it could always be mo...

tractortomck · tractortomck

Does anyone have information about this tractor configuration? How many were built? Any info is appreciated.

matthies · matthies

I drained the rearend to reseal the brake pinion shafts and now can't find anywhere to add other than the pto housing is this correct? I did find a check plug for the transmission is this used for the diff and trans? Not my tractor just one I working on for a guy that doesn't have a manual or wanting to buy one...

Topic		Started By	Replies	Views	Last Post
	Cockshutt 40 Distributor Bushings (Preview) Ive recently brought home a Cockshutt 40 with a 230 Buda. The distributor is pretty worn, with quite a lot of side to side slop in the shaft which is making setting the points a challenge. Its an Autolite IAD 6001 1B. Im having trouble locating a new bushing or mechanical advance springs. Any parts I have...	Fourty	1	504	10:14 AM Jun 23, 2023 by Fourty
	Governor rebuild (Preview) Can anyone recommend a good outfit, or person, to rebuild the governor for my 30?	Andrus	11	4904	09:33 PM Oct 23, 2021 by razmosis
	Identifying year of cockshutt 30 (Preview) Howdy yall Im new to the cockshutt tractors and just picked one up for 300 bucks. Am i right to assume its from late 1930s with the following cast number of 47-80-6043	Farmerbrowne	2	1718	08:12 PM Jun 4, 2018 by Mike(NEOhio)
	cockshut 30 starter (Preview) anyone knows if there is a replacement for the cockshutt 30 starter. something better. been rebuilding mine for the third time and still fail. thanks	colorado502	2	1782	11:36 AM Aug 4, 2017 by colorado502
	Cockshutt 30 gearshift (Preview) the gear shift moves all around in circles instead of in a precise gear shift pattern. For example I need to push the shifter to the left with my foot to get it in Reverse. Any thoughts out There? - Brett Baker	BBaker	2	2158	06:49 PM Dec 2, 2016 by Mike(NEOhio)
	Correct fluid for a Cockshutt 30 PTO? (Preview) Exactly as the title asks. I need to fill the PTO assembly with oil. What type does it take?	Kruser	2	2239	06:43 PM Sep 6, 2016 by Mike(NEOhio)
	30/E3 Steering (Preview) I am rather new to the Cockshutt/Co-op world, but I have noticed the the steering shaft seems to like to rust/freeze solid in the cast iron housing up by the instruments. What is the best way to get the shaft loose again?	Swen Nilsson	3	2079	07:29 PM Aug 28, 2016 by Mike(NEOhio)
	Source for oil fill tube? (Preview) Putting together a Buda 4B153 and I was wondering what would be the best source for a new oil fill tube. The block I am using doesn't have one. Before I start putting too much time into this, does anybody have a source for this or can you point me to the right direction?	Kruser	0	1915	07:16 PM Aug 27, 2016 by Kruser
	Cockshutt 30 front axle part (Preview) I recently acquired a Cockshutt 30. The one front wheel hub was off as the bearing was shot. I am trying to put things back to together. I have a diagram in a service manual, but not a parts book. There is a "washer" that apparently goes into the seal retainer. Is the "washer" a metal washer, or is it a f...	Swen Nilsson	2	2209	10:57 PM Aug 2, 2016 by Mike(NEOhio)
	1947 Coop E3 paint code? (Preview) I'm looking to repaint a 1947 Coop E3. The paint supplier wants a paint number before he will sell me any. Anybody wish to give me the correct paint number? TIA.	Kruser	0	2440	09:39 AM Mar 26, 2016 by Kruser
	Cockshutt 30 Wheels (Preview) I have some question's about the wheels on the Cockshutt 30's.when did Cockshutt start using the cast spoked rear wheels were these only on early or later tractors or were they an option.the same goes for the front wheels anybody know?.John -- Edited by JOHN PERUSELLO on Saturday 30th of March 2013 10...	JOHN PERUSELLO	3	3148	11:07 PM Mar 2, 2016 by JOHN PERUSELLO
	whats a 40 radiator worth (Preview) Hey guys whats this radiator out of a 40 worth. Was good when pulled been hanging in my garage since.	skinny9976	0	3044	04:04 PM Oct 9, 2015 by skinny9976
	Cockshutt 30 Ross Stearing Gear Box Seals (Preview) Need some help, restoring a 1953 Cockshutt 30, Stearing gear box is made by Ross W262999 and I cannot find the input shaft seal. The seal I pulled out of it has the numbers GK120N056 on it. Any help in finding a new seal is greatly appreciated	Neil	2	3245	12:51 PM Oct 7, 2014 by Mike(NEOhio)
	cockshutt 20 (Preview) I have a 1952 cockshutt 20 need wiring diagram to rewire it the wright way . Thanks alot	coope3	0	2507	01:23 AM Sep 21, 2014 by coope3
	50-D Wants to be a narrow front (Preview) Hi folks,I have a 50 wide front that I use to compete in antique tractor pulls with.After pulling for over 20 yrs. it is still very successfull pulling in classes over 6000 lbs.I've been thinking it's time to make a small change just to mix things up a bit.I would like to switch to a narrow front end t...	Buda	15	3797	04:31 PM Sep 18, 2014 by Buda
	50D Has hot starting issues (Preview) Hi folks:I have owned and loved Cockshutts for over 20 years,but am new to your forum.Please bear with me while I bore you with my Cockshutt story.When I got into antique tractor pulling about 25 yrs. ago.I wanted something differant then the Farmalls and JDs that were common around here,so I bough...	Buda	1	2806	07:54 PM Sep 15, 2014 by Buda
	Cockshutt 40 adjuistable wide Front Conversion (Preview) Looking for a little help. I am like Buda last year and want to put a narrow front on my 40 PD.. I have the wide front off and the shafts apart. Found a 30 narrow front and the cast pedistal bolts right up. The holes in the pedistall will need to be re-drilled to fit the tower. Looks like I will have to cut the sha...	dano	3	3649	07:30 PM Sep 15, 2014 by Buda
	Buda manual (Preview) See my post on the Buda section.	Mike(NEOhio)	0	2617	09:29 PM Jun 25, 2014 by Mike(NEOhio)
	spindle thrust brearing (50 gas) (Preview) Anyone have a part number for me? Unable to get to my cockshutt parts manual at the moment...timken number would be best!	ikeever	1	2360	08:53 PM May 24, 2014 by Mike(NEOhio)
	50 Gas piston slap (Preview) Ever since I put that thinner head gasket on my 50 gas, I've got considerable piston slap...does a thicker oil help with this at all? Synthetic oil? It is not bad, just looking for a way to quite it down a bit. Buda guys any tips?	ikeever	2	2422	09:23 AM May 23, 2014 by ikeever
	Cockshutt 30/co op e3 diesel info wanted (Preview) I just purchased a co op e3 diesel(paint underneath is orange) with serial number 30D33418 and was wondering a couple of things since I am new to these tractors. Where is the best place to get parts for this buda diesel? Where is the best place to get parts(new and used)in general for these? How many...	ndmcsx	9	4690	03:48 PM Dec 31, 2013 by Mike(NEOhio)
	New to me Cockshutt 30 (Preview) Just got my 30, wanted one for years, 8 spd, live power, question about gear shift - little pin on left side facing forward, moves in and out - not supposed to ? If it moves out too far, gear shift gets loose. Pulled it out , does not go all way through. How is this supposed to be held in? Pic attached, still som...	cowman61	3	2436	10:05 PM Dec 9, 2013 by Mike(NEOhio)
	Power steering pictures (Preview) Does anyone have any pictures of a power steering setup on a 50. I'm thinking about rigging one up and want it to look as close to stock as possible. isaackeever@gmail.com	ikeever	4	2512	05:58 AM Aug 22, 2013 by ikeever
	cockshut 30 need expertise help (Preview) started to run great at idle and then at full power,its run like if it was not breathing or maybe to much air, but idle run great, rebuit the fire and fuel system, still the same. anyone have any idea?	colorado502	1	2407	05:25 AM Aug 4, 2013 by mab570diesel
	1955 rcaf cockshutt 30 forklift (Preview) Hi My name is Lee. I'm from Nova Scotia, Canada. I have a 1955 Cockshutt. It's in good shape sheet metal wise. I'm wondering what this tractor is worth? If anyone has information on my machine it would be greatly appreciated.	lee troop	2	3199	04:24 AM Jun 28, 2013 by Craig
	parts book pages (Preview) Tenny, send me your email address by private message. I'll shoot you those front end diagrams.	Mike(NEOhio)	0	2403	02:49 AM Apr 27, 2013 by Mike(NEOhio)
	Cockshutt 40 (Preview) I have a chance to aquire a 40 but the original engine is out of it, what is the chance of finding an original engine? What is an adjustable wide front end for the same tractor worth?	reebok	2	2609	06:37 PM Mar 9, 2013 by Mike(NEOhio)
	Block heater for Cockshutt 30 (Preview) I am looking for advice on warming up the engine of my Cockshutt 30 before starting it (it's about to get very cold up here). There is very little space to put in a standard heater in the lower radiator hose. It's basically all metal with a small hose connecting the two parts. I suppose it could always be mo...	Daniel_Parent	1	22486	08:05 AM Dec 18, 2012 by idlem
	Cockshutt 30 Forklift --RCAF (Preview) Does anyone have information about this tractor configuration? How many were built? Any info is appreciated.	tractortomck	5	6230	02:53 PM Nov 18, 2012 by Michael
	Cockshutt 40 trans/differential check fill (Preview) I drained the rearend to reseal the brake pinion shafts and now can't find anywhere to add other than the pto housing is this correct? I did find a check plug for the transmission is this used for the diff and trans? Not my tractor just one I working on for a guy that doesn't have a manual or wanting to buy one...	matthies	1	2491	05:38 PM Sep 5, 2012 by Cockshutt560
1 2 3 > Last» \| Page of 3 sorted by