Buda

Jeffbo1 · Jeffbo1

Im considering rebuilding my engine in-frame this is for a 1947 Co-op E3 with the Buda four cylinder engine...has anyone done this and are there any tips? Id like to change the rod bearings, piston rings and send the head out to a machine shop for refreshing....does anyone have a good parts source? Man...

Milan · Milan

Greetings to all, I am helping a friend with a very early 1940's Buda 6 cylider diesel-generator used to run a well pump. The pump is being run perhaps a few times a year. This system was being serviced by another close friend of his, who unfortunately passed away a couple of years ago. So the unit has been...

Bill Friday · Bill Friday

I have located a Plymouth DLG standard gauge railroad locomotive, abandoned in the woods in North Alabama around 1950, in terrible shape but still possibly restoreable. The 55HP Buda 4-cylinder gas engine has a corner broken off the head so water has pooled there for no telling how many years. Other...

Mike(NEOhio) · Mike(NEOhio)

There are 20 studs for the head. Sixteen are 5 3/8". Four are longer for the water return flanges but two are 5 7/8 and two are 6 3/8. I can't remember which holes longer ones go into. Can anyone check theirs and post back? IIRC the 6 3/8 went to the rear flange and the 5 7/8 went under the thermost...

PaulBrownell · PaulBrownell

The valve on number 1 cylinder is stuck in my Buda 153. I've tried oiling it, tapping the valve top, prying the spring under the spring retainer and it will not free up. I let the engine heat up thinking that the casing would expand and let the valve stem go. All I succeeded in doing is bending the push rod. D...

Mike(NEOhio) · Mike(NEOhio)

I'm rebuilding an engine that's been apart for a long time. The two 3/8 plugs are for the oil passage through the block but I can't find a place for the 1/4 plug. The washer was with the distributor parts but doesn't fit anywhere on it. 9/16 ID, 11/16 OD, .060 thick, shiny from wear. Can anybody help?

ezed76527 · ezed76527

Just purchased a 4b182 out of a air compressor. It is a little different than the 4b153 as it has a magneto rather than a generator. I understand that the 182 is rather rare and that some people call them a power block. Anyone installed one of these in a "30"?? If so what is involved and...

Mike(NEOhio) · Mike(NEOhio)

The Buda service manual, I&T manual and COOP parts book all mention a felt oil wick in the ball end of the rocker arms. I've had a couple of them apart and have never seen any trace of a wick. Does anybody know the real story?

Mike(NEOhio) · Mike(NEOhio)

https://www.dropbox.com/s/fnr3oyalufp4i8o/Budamanual_lastpg.pdf?dl=0

Mike(NEOhio) · Mike(NEOhio)

For any and all who would like a copy you can download these off dropbox.com. Click each of the three links. OLD LINKS STOPPED WORKING AND NEW UPLOADS ARE IN PLACE. SEE NEW POST FOR LINKS. Manual is for gas engines 4B153, 4B184, 6B230 and 6B273. It covers general industrial and vehicle applications...

Mike(NEOhio) · Mike(NEOhio)

I finally got to it this week. I scanned the Buda engine manual into my PC in .pdf format. The book covers 4B153 and 182 and 6B230 and 273 gas engines. I'll be happy to share it. My thanks go out to Chuck Rhodes who copied it for me. He has a lot of records from the Harvey, Ill. plant but they're mostly from...

cmeador1984 · cmeador1984

Shop said mine is cracked, don't get on here much due to lack of traffic, but if anyone sees this c.meador1984@gmail.com

cmeador1984 · cmeador1984

Shop said mine is cracked, don't get on here much due to lack of traffic, but if anyone sees this c.meador1984@gmail.com

colorado502 · colorado502

looking for a gaz buda 4b153

Jeffbo1 · Jeffbo1

I have a further question beyond pulling the crank nut and belt pulley....I have read in my shop manual that in order to get the front cover off I will need to dismantle the governor as it is an integral part of the front cover...once the linkage is removed, is the governor case simply split by unbolting...

Jeffbo1 · Jeffbo1

I need to change the front oil seal on my E3's Buda engine....I saw the earlier post about this but need simply to know which way the hand crank nut turns in order to remove it and thus the pulley behind so i can remove the front cover etc. etc....I think a pipe wrench is the only tool that will grab the nut suf...

Duke 40 · Duke 40

Can I repair a crack in the side wall of my Buda gas engine? I am researching types of pinning technics. I am nervous about the strength after it's done and will I be able to place a load on the engine in the future. I want to use the tractor for farming and pulling.

CA_Neil · CA_Neil

I have an old Buda engine in my machine shop. Came with the property I bought. Should I scrap it or is it of some value to someone? If someone is interested, I will see what identifying info is on the engine and/or take pics.

agyuro · agyuro

Hi All, What is the purpose of the screw in the front of the govenor housing. Do you need to prime with oil ?? or is this for see if oil fills inside when running ?? A little exeprtise on the use and function of this screw. Photo attached for clarity. Thanks, Tony

Buda · Buda

Hi folks,I posted this question a few weeks ago but not in the right area.I have a 50D deluxe that I mainly use at antique pulls and parades.I'm sure it's Buda engine has lots of running time on it but it's power still checks out real good on a dyno(62 hp@535 pto rpm w/ the pump turned up to peak performa...

Canoe30 · Canoe30

Hello I have a bottom pulley on my 30 that has come loose I was able to post the video on the Cockschutt Facebook page you can view it there but any suggestions how I get this nut off and replace my pulley is very much appreciated thanks

sidbec · sidbec

What is the amerage draw for the E-3 starter?

agyuro · agyuro

What is the weight of the buda engine ?? anybody know or provide a guestimate ??

coop Bob · coop Bob

Any one know when the stationary or Gleaner G262 engines where painted orange and not Gray. I bought one for a transplant and it is orange. My guess would be late in the the production or from a Gleaner F

johnny cockshutt · johnny cockshutt

i'm looking for a new engine for my 30, anyone out there have a running or repairable 4b153? -- Edited by johnny cockshutt on Wednesday 13th of July 2011 12:00:01 PM

agyuro · agyuro

I have an oil leak at the front behind the crankpulley, suspect the oil seal in the crankcase needs to be replaced. But, I can't get the pully bolt / jawnut off. Any suggestions here. Please be descriptive as I would like to take the pulley nut off as easy as possible. Great site!!

Mike(NEOhio) · Mike(NEOhio)

I'm rebuilding a 6B230 for an E4 and looking for new rocker arm clips (see attachment). The tips are badly worn. I have two E3's in the same condition so I'd bet it's a common problem. Does anyone know of a source? If there is enough demand I would consider making them for sale. Opinions welcome. Mik...

Sudsy · Sudsy

I'm looking for a 4 cylinder Buba diesel. The block that I have is cracked and can not be fixed. The engine's in my Farm Master tractor.

Sudsy · Sudsy

I have a Farm Master tractorand I'm looking for a 4 cylinder Buda diesel motor. To my understanding, the tractor was a cross between a Cockshutt & a Coop. Have any of you ever seen a Farm Master or know where I can find some information about the tractor? Thanks, Sudsy

agyuro · agyuro

Hi All, I have reinstalled the buda engine due to a front oil seal leak and all went OK. There is no leaks but at the front of the Govenor. So I tightened the botls a bit more as I used Permatex The Right Stuff gasket maker. When I tightened and ran the motor and the front of the govenor started to turn red HOT...

Topic		Started By	Replies	Views	Last Post
	Has anyone done an In frame engine overhaul? (Preview) Im considering rebuilding my engine in-frame this is for a 1947 Co-op E3 with the Buda four cylinder engine...has anyone done this and are there any tips? Id like to change the rod bearings, piston rings and send the head out to a machine shop for refreshing....does anyone have a good parts source? Man...	Jeffbo1	0	535	05:58 PM Mar 20, 2024 by Jeffbo1
	Buda priming pump (Preview) Greetings to all, I am helping a friend with a very early 1940's Buda 6 cylider diesel-generator used to run a well pump. The pump is being run perhaps a few times a year. This system was being serviced by another close friend of his, who unfortunately passed away a couple of years ago. So the unit has been...	Milan	0	632	02:47 AM May 29, 2022 by Milan
	Buda 55HP 4-cylinder gas engine - rebuild or find a replacement? (Preview) I have located a Plymouth DLG standard gauge railroad locomotive, abandoned in the woods in North Alabama around 1950, in terrible shape but still possibly restoreable. The 55HP Buda 4-cylinder gas engine has a corner broken off the head so water has pooled there for no telling how many years. Other...	Bill Friday	1	4241	09:24 PM Feb 20, 2016 by Mike(NEOhio)
	230 gas, head studs (Preview) There are 20 studs for the head. Sixteen are 5 3/8". Four are longer for the water return flanges but two are 5 7/8 and two are 6 3/8. I can't remember which holes longer ones go into. Can anyone check theirs and post back? IIRC the 6 3/8 went to the rear flange and the 5 7/8 went under the thermost...	Mike(NEOhio)	0	2568	07:58 PM Sep 27, 2015 by Mike(NEOhio)
	Stuck valve (Preview) The valve on number 1 cylinder is stuck in my Buda 153. I've tried oiling it, tapping the valve top, prying the spring under the spring retainer and it will not free up. I let the engine heat up thinking that the casing would expand and let the valve stem go. All I succeeded in doing is bending the push rod. D...	PaulBrownell	2	2004	06:45 PM Jun 28, 2015 by PaulBrownell
	230 gas, help with two parts needed (Preview) I'm rebuilding an engine that's been apart for a long time. The two 3/8 plugs are for the oil passage through the block but I can't find a place for the 1/4 plug. The washer was with the distributor parts but doesn't fit anywhere on it. 9/16 ID, 11/16 OD, .060 thick, shiny from wear. Can anybody help?	Mike(NEOhio)	0	2441	06:31 PM May 10, 2015 by Mike(NEOhio)
	buda 4b182 (Preview) Just purchased a 4b182 out of a air compressor. It is a little different than the 4b153 as it has a magneto rather than a generator. I understand that the 182 is rather rare and that some people call them a power block. Anyone installed one of these in a "30"?? If so what is involved and...	ezed76527	7	4510	02:14 PM Apr 14, 2015 by thecoopkid
	Felt oil wicks in rocker arms. (Preview) The Buda service manual, I&T manual and COOP parts book all mention a felt oil wick in the ball end of the rocker arms. I've had a couple of them apart and have never seen any trace of a wick. Does anybody know the real story?	Mike(NEOhio)	1	2112	10:05 PM Apr 13, 2015 by PaulBrownell
	New links for Buda manual for gas 153, 184, 230 and 273 engines. (Preview) https://www.dropbox.com/s/fnr3oyalufp4i8o/Budamanual_lastpg.pdf?dl=0	Mike(NEOhio)	1	3225	09:58 PM Oct 19, 2014 by PaulBrownell
	Buda engine manual (gas only) download (Preview) For any and all who would like a copy you can download these off dropbox.com. Click each of the three links. OLD LINKS STOPPED WORKING AND NEW UPLOADS ARE IN PLACE. SEE NEW POST FOR LINKS. Manual is for gas engines 4B153, 4B184, 6B230 and 6B273. It covers general industrial and vehicle applications...	Mike(NEOhio)	0	2557	09:26 PM Jun 25, 2014 by Mike(NEOhio)
	Buda engine manual (Preview) I finally got to it this week. I scanned the Buda engine manual into my PC in .pdf format. The book covers 4B153 and 182 and 6B230 and 273 gas engines. I'll be happy to share it. My thanks go out to Chuck Rhodes who copied it for me. He has a lot of records from the Harvey, Ill. plant but they're mostly from...	Mike(NEOhio)	2	2980	09:50 PM Jun 24, 2014 by CeasarRoman
	need BUDA 153 head for my E3 (Preview) Shop said mine is cracked, don't get on here much due to lack of traffic, but if anyone sees this c.meador1984@gmail.com	cmeador1984	0	2306	10:00 AM Apr 14, 2014 by cmeador1984
	need BUDA 153 head for my E3 (Preview) Shop said mine is cracked, don't get on here much due to lack of traffic, but if anyone sees this c.meador1984@gmail.com	cmeador1984	0	2088	09:34 AM Apr 14, 2014 by cmeador1984
	buda engine (Preview) looking for a gaz buda 4b153	colorado502	0	2315	08:07 PM Mar 20, 2014 by colorado502
	Front oil seal replacement, further question regarding the governor on my Co-op 30's Buda 4 cylinder (Preview) I have a further question beyond pulling the crank nut and belt pulley....I have read in my shop manual that in order to get the front cover off I will need to dismantle the governor as it is an integral part of the front cover...once the linkage is removed, is the governor case simply split by unbolting...	Jeffbo1	2	2394	11:54 PM Dec 9, 2013 by Jeffbo1
	Co-op E3 Buda engine lower front pulley question (Preview) I need to change the front oil seal on my E3's Buda engine....I saw the earlier post about this but need simply to know which way the hand crank nut turns in order to remove it and thus the pulley behind so i can remove the front cover etc. etc....I think a pipe wrench is the only tool that will grab the nut suf...	Jeffbo1	3	2406	01:02 PM Dec 8, 2013 by Jeffbo1
	Cracked Block Buda B230 (Preview) Can I repair a crack in the side wall of my Buda gas engine? I am researching types of pinning technics. I am nervous about the strength after it's done and will I be able to place a load on the engine in the future. I want to use the tractor for farming and pulling.	Duke 40	8	4735	04:20 PM Oct 9, 2013 by rriley
	What do I do with an old Buda Engine (flat-head, 6 cyl)? (Preview) I have an old Buda engine in my machine shop. Came with the property I bought. Should I scrap it or is it of some value to someone? If someone is interested, I will see what identifying info is on the engine and/or take pics.	CA_Neil	2	2772	04:15 PM Oct 9, 2013 by rriley
	screw in front of govenor housing ??? What is it's purpose ?? (Preview) Hi All, What is the purpose of the screw in the front of the govenor housing. Do you need to prime with oil ?? or is this for see if oil fills inside when running ?? A little exeprtise on the use and function of this screw. Photo attached for clarity. Thanks, Tony	agyuro	4	3820	12:51 AM Jun 2, 2013 by Mike(NEOhio)
	Hard starting hot Buda (Preview) Hi folks,I posted this question a few weeks ago but not in the right area.I have a 50D deluxe that I mainly use at antique pulls and parades.I'm sure it's Buda engine has lots of running time on it but it's power still checks out real good on a dyno(62 hp@535 pto rpm w/ the pump turned up to peak performa...	Buda	0	2185	06:37 PM Apr 7, 2013 by Buda
	Bottom pulley fix/replace Cockschutt 30 (Preview) Hello I have a bottom pulley on my 30 that has come loose I was able to post the video on the Cockschutt Facebook page you can view it there but any suggestions how I get this nut off and replace my pulley is very much appreciated thanks	Canoe30	1	2393	01:32 AM Apr 8, 2013 by Mike(NEOhio)
	What is the amperage draw for an E-3,Buda engine. Seems like the starter is not turning the motor over fast enough [new (Preview) What is the amerage draw for the E-3 starter?	sidbec	2	2831	05:43 PM Oct 31, 2012 by JAMESCOUSINS
	Weight of the Buda 4 cyl - ?? in pounds (Preview) What is the weight of the buda engine ?? anybody know or provide a guestimate ??	agyuro	3	3014	02:55 AM Oct 17, 2012 by Mike(NEOhio)
	Allis G262 (Preview) Any one know when the stationary or Gleaner G262 engines where painted orange and not Gray. I bought one for a transplant and it is orange. My guess would be late in the the production or from a Gleaner F	coop Bob	0	3149	05:28 AM Jul 14, 2012 by coop Bob
	30 engine wanted (Preview) i'm looking for a new engine for my 30, anyone out there have a running or repairable 4b153? -- Edited by johnny cockshutt on Wednesday 13th of July 2011 12:00:01 PM	johnny cockshutt	2	2898	12:04 PM Jul 14, 2012 by Co-op Johnny
	Cockshutt 30 - Buda 4 Cyl - Crankcase Oil Seal Leak at Front - remove crankjaw nut (Preview) I have an oil leak at the front behind the crankpulley, suspect the oil seal in the crankcase needs to be replaced. But, I can't get the pully bolt / jawnut off. Any suggestions here. Please be descriptive as I would like to take the pulley nut off as easy as possible. Great site!!	agyuro	5	4541	12:24 AM Apr 30, 2012 by Mike(NEOhio)
	Buda rocker arm clip (Preview) I'm rebuilding a 6B230 for an E4 and looking for new rocker arm clips (see attachment). The tips are badly worn. I have two E3's in the same condition so I'd bet it's a common problem. Does anyone know of a source? If there is enough demand I would consider making them for sale. Opinions welcome. Mik...	Mike(NEOhio)	0	2780	01:13 AM Apr 23, 2012 by Mike(NEOhio)
	Buda Diesel (Preview) I'm looking for a 4 cylinder Buba diesel. The block that I have is cracked and can not be fixed. The engine's in my Farm Master tractor.	Sudsy	2	2640	04:25 PM Dec 27, 2011 by Doug550
	Buda Diesel (Preview) I have a Farm Master tractorand I'm looking for a 4 cylinder Buda diesel motor. To my understanding, the tractor was a cross between a Cockshutt & a Coop. Have any of you ever seen a Farm Master or know where I can find some information about the tractor? Thanks, Sudsy	Sudsy	2	3592	08:41 AM Dec 27, 2011 by Sudsy
	RE: Cockshutt 30 - Front of Govenor Overheating (Preview) Hi All, I have reinstalled the buda engine due to a front oil seal leak and all went OK. There is no leaks but at the front of the Govenor. So I tightened the botls a bit more as I used Permatex The Right Stuff gasket maker. When I tightened and ran the motor and the front of the govenor started to turn red HOT...	agyuro	1	4698	06:24 PM Nov 29, 2010 by Cockshutt560
1 2 > Last» \| Page of 2 sorted by